R.D. Mathis Company - High-Vacuum Evaporation Sources   Request a FREE Catalog!



Company Info About Us Product Info Equipment Info Tech Info Home Page Questions Contact Us
Add me to your mailing list!
Shop Online Now! NEW!
Click here to view our catalog
View our evaporation source catalog


Frequently Asked Questions

 
Listed below are questions and answers regarding evaporation materials, techniques and proper source selection that may help address issues that apply to your thin film coating process.

 
Q. I would like to evaporate aluminum onto a glass substrate. What evaporation source would be best?
 
A. Aluminum can be successfully thermally evaporated with several sources including a filament, boat or crucible. The correct source for your needs depends on the power you have available from your transformer, the volume of aluminum to evaporate and the distance from your source to substrate. Generally, a tungsten filament or boat will work very well for most evaporations.
 
 
Q. Is there a way to evaporate silicon monoxide (SiO) to create thin fim coatings without pinhole defects?
 
A. SiO has a tendancy of "spitting and streaming" during evaporation which will result in pinhole type defects in most coating applications. One way to reduce the particulates in your vapor stream is to use a "multi-baffled box source". This type of source positions your evaporant material in two separate cavities, when heated it follows an indirect path through a series of baffles and then out the vertical chimney. Your substrate cannot see the bulk material at any time, this essentially eliminates any chance of spitting and streaming which can cause pinhole type defects. This type of source is pictured , with various configurations, on pages 31 through 34 of our catalog. Also, see our list of SiO related articles available to you on our "Technical Information" page.
 
 
Q. When evaporating gold, I find that alot of my material "creeps" out of the evaporation area and wets to the leads of my boat source. I end up using more gold than I should. Do you have any recommendations for eliminating this problem?
 
A. One solution is to use an alumina coated boat source. The alumina, which is plasma coated on to the evaporation boat acts as an inert surface and prevents the gold from wetting to it. Also, when the gold melts it forms a sphere resulting in point source performance. This type of source gives long life compared to uncoated sources. A variety of alumina coated sources are pictured on pages 23 through 27 of our catalog.
Another recommendation is to consider using a crucible and crucible heater to hold and heat your material. Crucibles also privide a focused evaporation pattern and are available in several ceramic and metallic configurations.
 
 
Q. My evaporator is capable of putting out 50 - 60 amps maximum and I would like to deposit small amounts of aluminum and nickel. Is there one source that would work for me?
 
A. Your best choice would be to use a tungsten filament or basket. Although nickel has a much higher melting point than aluminum, many tungsten filament and basket configurations are capable of reaching high enough temperatures for both materials. The materials you mentioned are somewhat corrosive when melted, with nickel being the most corrosive. This will lead to the eventual deterioration of the filament or basket. Another alternative would be to use a tungsten basket heater with the appropriate crucible. Although this will require slightly more power, the deterioration will be minimized and both the basket and crucible will provide several uses.
 
 
Q. My application requires an adhesion layer of chromium. Is there an easy method of depositing chromium.
 
A. Yes. A "Chrome Plated Tungsten Rod" is a simple and user friendly way to deposit thin layers of chrome. These rod sources provide good thermal efficiency, regulation of film thickness and elimination of spalling. More information is shown on page 37 of our catalog.
 
 
If you have questions about thermal evaporation or would like to discuss improvements in your process, please give us a call.
We look forward to hearing from you
.
                                                                                                                                    
Company Info | About Us | Product Info | Equipment Info | Technical Info | Contact Us | FAQ | Homepage | View Catalog

Your best choice for quality hi-vacuum evaporation sources.
R.D. Mathis Company
Call Us:
P.O BOX 92916, Long Beach, Ca  90809-2916 Telephone (562) 426-7049 Fax (562) 595-0907